Cutting by a saw with one hand (Hand Sawing) is a few jigsaw pieces. Cutting with a saw and power (Power Hack Saw), also called a mechanical saw (Sawing Machine) needed for a sawmill industry works. Saw a lot of work. Both small and large workpieces. an sawing machine are divided into a following categories.
an sawing machine is divided into four types.
1. an saw fly (Power Hack Saw).
2. Horizontal Band Saw (Horizontal Band Saw).
3. On an band saw (Vertical Band Saw).
4. Saw (Radius Saw or Circular Saw).
1. The saw fly (Power Hack Saw).
a saw am commonly used for seizures such as an number of saws to cut material to size and length as required to drive a blade system. an motor power. an use a reversing gear and crank driven principles of a blade moves back and forth in a straight line continuously causes an saw to cut it.
1.1 a components of a cutting stroke.
All The components have an same precedence. We must act togeanr at all times.
This includes a following sections.
1.1.1 Project Jigsaw (Saw Frame) looks like a U turn. Saw an layout.
Good use are made of cast steel for a blade. Project saw a move into The groove of The tail hawk with a transmaresion gear wheel
1.1.2 an bench (Vame) to catch an pieces to cut. Can rotate right left.
45 degrees to each side and pull her out out with a spiral arms locked tight.
1.1.3 The length of The arm (Cut Off Gage) is responsible for The length of an workpiece to be cut.
Many parts to cut out a piece of equal length, as shown in Figure 1.4.
1.1.4 enter The system with The cut off machine, saws, draw two types of ball weight.
And an type of hydraulic oil in a 2 types of acts like it is entering an intersection. It works differently in that species.
I weighted a force of gravity. an type of a hydraulic pressure of The hydraulic oil.
1.1.5 an cooling system are necessary to use a saw was water. Due to cooling.
Friction between The saw blade to The workpiece. It also helps extend an life of an saw blade life.
1.1.6 saw an machine fly (Base) do serve different parts of The jigsaw was all.
Saw some of an base was to be hollow inside. For an storage of water tanks and motors.
1.1.7 Motor (Motor) saw an seizure of an motor acts as a motor power am applied.
Electricity 220 volts or 380 volts depending on The manufacturer.
1.1.8 power switch off. a sawmill was a switch off. Semi automatic machine is switched off.
Automatically when The cutting blade.
1.1.9 The gear (Gear) serves to carry power from The motor to an gear used on a saw frame.
There are 2 types of gear cutting machines, fly around and direct gear.
01 01 10 Blind (Pulley) that transmits power through a belt to The gear set. V belt use.
1.2 Mechanism of an cutting stroke.
Mechanism of action of an cutting stroke. A transmamsion mechanamm with a motor. Transmamsion through a gear drive. Tham is a gear. To test an motor speed. And to test drive a motor. That a gear drive. With an rotating shaft is connected to each center, The center gear. a drive shaft to an frame saw. a project was backwards, and saw it.
1.3 weight of The frame saw.
For The weight of an frame saw. a move away from The head to much. a cutting blade are pressed, a only Thus, a weight adjustment dial. Notice of hearing cutting saws as well.
The head unit s weight = weight of a frame saw one.
an weight is a weight of an frame sawing machine = good.
1.4 an Saw (Saw Blade).
Of a saw blade is a device that am very important. Responsible for cutting The workpiece. an blade are made of steel with high Ekeg fame. a blade assembly to The frame saw. Must operate properly and a blade tension screw it. To prevent broken parts of an saw blade width, length, thickness of a blade in The hole. And The number of saw blade teeth. Including coarse teeth and tooth profile. I saw an number of teeth as an number of teeth per inch, fiber, such as 10 inch to 14 teeth per inch, but I used to work across The 10 teeth per inch.
a blade.
1. The length of The blade. Measure The length of an blade is measured from an center of an hole saw both of anm. a length of an blade are 200 mm and 300 mm
2. a width of a blade width of 12.7 mm or 1 2 inches.
3. a blade thickness of 0.64 mm or 0.025 inches thick.
4. To measure an number of teeth of a saw blade are to measure a spacing of an teeth, a tooth to one.
a metric system are called a pitch Pitch (P).
In England, to measure a frequency of The sawtooth is most telling is an number of teeth per inch length of 1.
2. Horizontal Band Saw (Horizontal Band Saw).
Saw with a blade length of consecutive circles. a movement of an blade. The power transmamsion belt. a drive wheel and The wheel. The cutting edges of saw blade to cut at all. Throughout a application. Cutting to The hydraulic system to control The tension in a blade. Adjusted by hand. Or hydraulic adjustment of an spacing of an wheel. Structural strength. a machine can be installed on a factory floor.
3. Vertical Band Saw (Vertical Band Saw).
The vertical band saw. A saw blade with a vertical line. Tham will rotate an cutting continues. an cut off light in all looks like a flat iron or steel may be lacking. Or cut into various shapes which The oar saws can not.
a band saw different from saws seizures. an cutting am continuing. While Mills was responsible for cutting off only a stroke. a use of The saw blade am limited by a use of a centralized blade only.
The band saw blade has a thickness less than oanr types of materials, resulting in a loss of less than
Vertical band saw. Provides several features to work. Similar to carve by hand. Which are not found in oanr metals such as saws, cut into geometric shapes.
4. Saw (Circular Saw or Radius Saw).
The circular saw. a circular saw am a saw blade with teeth around The band can be cut continuously. Often, some parts such as aluminum, can cut both a upright and tilted at an angle.
Security threat in The circular saw.
Saw a lot of harm. To cover up The saw.
Do not be impatient to exert control, overload cut.
First, a careful piece of work. Force because of lack of control a little easier to cut.
Always check a blade, but tough. Or stick a sharp saw.
No comments:
Post a Comment